Golden Snitch Prop

It's the Golden Snitch!

This is a really quick project but requires a few tools. Here's how to make your own Snitch like this one.

Tools:

• hot glue gun & one hot glue stick
• electric drill (e.g. a Dremel with a drill bit)
• scissors
• fine-tipped paint brush
• blunt/wide-tipped paint brush

Materials:

• a wooden ball
• two yellow feathers
• gold acrylic paint
• light yellow acrylic paint

All of the above (excluding the drill, perhaps) should be available from your local craft store.

Directions:

1.  Using a drill bit the same size as your feather stems, drill two holes in the wooden ball, angling the hole in the direction you want the feather to come out.
2. Stick the feathers into the holes to make sure they fit. Use scissors to trim the feathers to your desired length. Then take the feathers back out of the holes.
3. One hole at a time, squeeze hot glue into the hole and then shove the tip of the feather in. Before the glue cools, twist the feather so it's facing the right direction. Then repeat for the other hole and feather and let the glue cool.
4. Using a blunt-tipped brush, paint the ball gold. To minimize brushstrokes and keep the nice wood grain visible, paint on a very light layer, let it dry, then add one or two more layers of paint until the wood color is covered.
5. Using a fine-tipped paint brush and light yellow paint, detail on a design to give your Snitch an aerodynamic, athletic, or magical appearance. I just made up a design, but if you want you could find reference photos from the Harry Potter movies and try to create a movie-accurate Snitch. You'll note the "real" Snitch is not a completely smooth ball. To add texture, you could use gold puffy paint to "draw" the design on.
6. Finish with a light coat of gold over the light yellow. I also edged the yellow with a darker gold to give it the illusion of depth.

Cosplay Progress - Final Fantasy XIII-2 Lightning Wing 0.3

Today we'll be focusing on the feather skirt on the left side of Lightning.  I dont know what to call it, I thought of it as a wing, but a girl on DeviantArt referred to it as a feather skirt which sounds more appropriate.  This project ended up turning out a lot better than I assumed it would and costed less than I assumed.  I bought $25 in feathers and ended up only using 2/3s of it.

Ingredients

1. A Few Large Trimmed Feathers
2. A Few More Media Trimmed Feathers
3. A Lot More Small Trimmed Feathers
4. A Lot More Small Fluffy *cheap* Feathers
5. Buckram or some other stiff white fabric. We don't want a flimsy fabric or else it won't keep it's shape, but we dont want stiff material because it should still flow a little in the wind as you walk.  Another alternative would be craft foam.  Honestly I used Buckram just because it's light, white, and just sitting in front of my face while I was thinking about this project.
6. Hot Glue

1)      Cut out a piece of buckram in the shape of an outline of the wing.  It will serve as the backing for the wing, and we will be trimming it later

2)      We want a single feather to be our tip, start with one large feather and lay it pointing out of the bottom tip of the wing, remember that the buckram is serving as our outline so stay inside the lines.

3)      Glue the tip of the bone to the buckram.  We want to limit how much glue we use for several reasons.  A) more glue means more weight which adds no value.  B) more glue down the bone means less freedom for it to shift in the wind.

4)      From there we continue moving up arranging and gluing the large feathers. Follow these arrangement guidelines.

a.       The bone tip should be near the vertical center of the buckram.  Never glue near the edge of the buckram.

b.      Arrange the feathers in different angles but all pointing down (South, Southeast, or Southwest).  Making them all parallel will make it look too manicured. 

c.       Don’t put them all in a row, vary the vertical and horizontal placement of the feathers

5)      Once you’re done with the large feathers you can begin mixing feathers.  Start off my covering a horizontal area* with the fluffy feathers to completely cover up the buckram.  Keep the same guidelines as above, especially not gluing to the edge of the buckram.

*Only do one horizontal area at a time so you can layer the feathers on top of each other as you continue up.

  

6)      Lay a few of the trimmed feathers on top of the fluffy feathers.  You can mix the medium and small feathers, or you can use the medium first and the smaller ones up north.  Up to you.

7)      Repeat steps 5 and 6 until you’ve reached the top.  Because the top line is covered up my the belt for lightning you can skip this step, but I’ll include it for anyone who’s making a wing for other projects. Cover the top row with fluffy feathers.  In this case they should point to all different direction and glue up and past the edge.  The fluffy feathers should use one another to try to cover up their bones.

8)      Now you’re complete with one side of the wing.  Time to start trimming.  We want to trim off as much of the “boarder” of the buckram so that the feathers on the edge are hanging off.  I try to cut off as close to any glued spots as possible. 

Depending on your project you may not need a back, or you may need to only fill up a portion of the back, or may need to fill up all.  Just remember to think about your cosplay being viewed from all angles of a sphere.  In the case of Lightning, pieces of the inner side of the wing will be visible as I walk, so I do want to cover it up. 

9)      I usually more of the nicer feathers for the front and save more of the cheaper feathers for the back since they won’t be viewed as often.  From here you repeat steps 4-7 again.